The inner diameter or I.D. of the patio furniture part is the inside dimension of the patio furniture chair leg or arm. The inner diameter is the measurement from the inside wall of the patio chair leg to the opposite inside wall. The inner diameter can be easily measured with a tape measure.
The outer diameter or O.D. is the measurement from the outside wall of the chair leg/arm to the opposite. This dimension can be taken with a tape measure.
A multi gauge insert has flanges on it that allow for the patio furniture part to be fitted into various sized holes. The flanges on the part will flex and bend as the glide is inserted into the patio furniture chair leg or tube.
The total overall length of the solid shank rivet (30-512) is 0.60 inches, the short shank rivet (30-516) is 0.70 inches, the long shank river (30-515) is 0.80 inches in length
The 30-613 (1 ¼" diameter) and 30-614 (1 ½" diameter) are the most common glides for wrought iron furniture. These glides typically fit into a steel weld cup at the bottom of the chair or table leg. A more durable alternative would be the 1 ¼" or 1 ½ Forever Glides for wrought iron.
Both the 30-614 and 30-614 have a depth of ½". The glide also has small ribs around the outside to keep the glide firmly in place inside of the steel weld cup.
A disk cap typically sits around the outside of a patio furniture chair, patio furniture table or chaise lounge leg. Disk caps are usually very shallow, no more than ¼" deep. Disk caps were commonly used on very old wrought iron furniture that had a flat circular steel disk or washer, about the size of a silver half dollar, welded to the bottom of the leg. The disk cap would fit on to the OUTSIDE of the flat circular washer or disk. On the other hand, glides typically fit into the inside of the leg and have more depth or thickness.
The disk caps that we offer are approximately ¼" high. They are very shallow so they can snugly fit around the flat circular disks commonly welded to the bottom of very old wrought iron patio furniture.
A coved stem bumper has a rounded area cut out of the part which allows the stem bumper to sit along a round swivel base.
An end cap is typically an ornamental piece that is used to cover the extrusion end or open end of a chair frame to give the chair a finished look. End caps are commonly used for sling style furniture. Each manufacturer uses a slightly different sling rail extrusion. Please check carefully before ordering to determine the correct end cap required. In addition, end caps should NOT be used as glides. They are not strong enough or thick enough to endure the wear and abrasion.
If your wrought iron furniture chair legs have rusted and deteriorated over time, replacement metal cups or steel weld cups for wrought iron furniture can be purchased from us. See out miscellaneous parts section and look for part number 30-408. The companion plastic glide that works with this metal cup is 30-614. This can be found in the round glides and inserts section of our web site. The new steel weld cups for your wrought iron furniture can be welded to your chair legs. The remnants of your old weld cup must first be removed with a disc grinder or similar tool.
Yes, both the four position and six position adjustment brackets have three pre-drilled holes. It is often necessary to drill new holes into your chair frame to accommodate the positioning of the holes on the new brackets. The specs are as follows:
The 30-904 is approx. 9 ½" long. The end holes are spaced 4 ½" and 4 ¼" from the center hole.
The 30-908 is approx. 10 ½" long. The end holes are spaced 3 ½" and 5 ¼" from the center hole.
Replacement screws are NOT supplied with this part. You can buy replacement screws from your local hardware store.
The 30-905 has a 7 ½" hole-to-hole dimension.
The 30-906 has an 8 ½" hold to hole dimension.
Both of these part numbers have a ¼" bolthole. Replacement bolts are NOT supplied with this part. You can buy replacement bolts at your local hardware store.
Unfortunately, we do not carry longer glider arms. The only way to extend the glider arms would be to sever two of them and weld them together at the body to make one longer arm
If you still have your old spring plates, use them as a template to mark your new holes. Otherwise, use the holes on your swivel assembly for reference. Use a 3/8" drill bit to drill the new holes. The fiberglass spring plates on our web site are black in color. They can easily be spray painted to match the color of your patio furniture.
We strive to make as many patio furniture repair parts as possible available to our customers. Unfortunately, many newer styles of outdoor patio furniture are manufactured overseas and as a result, patio furniture replacement parts are not made available. We only carry the most common outdoor patio furniture parts for the most common styles/brands of outdoor furniture. If you do not find the outdoor furniture parts you need on our web site, we recommend checking with the original manufacturer of your patio furniture. There are so many outdoor furniture parts available, it would be impossible to stock all every outdoor furniture part for every manufacturer.
No, please. We are a small company and do not have the staff available to handle custom outdoor furniture parts requests and patio furniture part identification. Our website offers a detailed description of the patio furniture repair parts we carry and should give you the information you need to identify your patio furniture replacement part, glide, end cap or common wear part. Unfortunately, we do not offer every patio furniture replacement part available. Many of the patio furniture manufacturers have parts that are made specifically for their line of patio furniture. Our patio furniture, replacement part collection is generic in nature. Our outdoor furniture replacement parts can be used on any number of patio furniture collections. If you need a specific patio furniture replacement part, please contact your local outdoor patio furniture dealer.